Jump to content


Photo

Upgrade?


  • Please log in to reply
36 replies to this topic

#21 Stormy{CAN}

Posted 29 May 2007 - 09:18 AM

SATA doesn't have Master and Slave.

#22 Monkey

Posted 29 May 2007 - 11:42 AM

Wasn't even thinking when he asked I just did that thing we shouldn't do. I saw jumpers and slave/master. I suppose it doesn't matter what he sets his IDE drive to, I would suggest to master so if he was to add another drive things are seen in the same order they are now then.

#23 DarkFall

Posted 30 May 2007 - 02:06 AM

Regardless of what the system sets the drive names to, he can go into the manager and set them to what he wants or needs...

#24 Jac3624

Posted 30 May 2007 - 02:56 AM

Except for C:, that can never be changed.

#25 DarkFall

Posted 30 May 2007 - 02:12 PM

Except for C:, that can never be changed.


You removed your C: drive, according to what you told us, so I saw no need to state the obvious.

#26 Jac3624

Posted 31 May 2007 - 01:17 AM

Ok, on to the next thing.

What would be a good sound card to get that's not too expensive?

My board only has 2 PCI and 2 PCIe x1 slots. One of the PCI slots is taken for a tv card and the other is really close to my vid card. I would like to use at least one of those PCIe slots for something. Is there a sound card that uses that?

#27 Jac3624

Posted 01 June 2007 - 08:11 PM

DAMN!!! I can't get windows to install to my new drive.

#28 DarkFall

Posted 02 June 2007 - 03:15 PM

DAMN!!! I can't get windows to install to my new drive.



We need some particulars to work with here... Is the drive not being recognised, or what?

#29 Jac3624

Posted 02 June 2007 - 10:17 PM

Inside the working installation the SATA drive is recognized, but when I try to do a fresh install it's not being recognized.

I don't know how to make it install, but I know that it can be done.


This SS is from windows:
Posted Image
The 2 that are selected are the partitions of the SATA drive.

Someone on another board thought I was saying that I wasn't getting it to show up here, but I can as you can see. Just not when installing windows.

Just though I would clear up any possible confusion before it happened.

#30 Catfish

Posted 03 June 2007 - 08:58 AM

Windows XP installer won't recognize SATA drives, you have to make a driver disk to load the drivers. There should be instructions for this in your motherboard manual, it's pretty easy. It usually involves the driver cd that came with the motherboard. If you don't have that you should be able to track it down on their web site.

Then when you boot to the XP CD to install, it will say at the bottom "Press F6 to load RAID or SCSI drivers" - or something like that, it's been 2 years since I installed. Anyway, hit whichever it is, windows will load the device driver off the floppy and you're off to the races.

If you're still having trouble just google "installing windows to sata"

#31 Stormy{CAN}

Posted 03 June 2007 - 09:14 AM

What catfish dais or you can use nlite,

http://www.nliteos.com/

and slipstream the sata driver in, then there is no need for a floppy. Alternatively you can also check in the bios and see if it is possible to set the drive to ide mode, and you won't need the driver to install.

#32 Jac3624

Posted 03 June 2007 - 02:59 PM

Would I be able to burn the drivers to a cd? I don't even have a floppy drive, just didn't see the point.

#33 Stormy{CAN}

Posted 03 June 2007 - 03:35 PM

Download and install nlite, and while you're at it download the latest drivers for your motherboard (ULI ® M1573Chipset, version 2.20),

http://www.nvidia.co...li_drivers.html

then extract the file using Winrar and locate the inf for the sata driver (going to need this for later. Next copy over your XP cd onto the hard drive, then run nlite and load the copied over cd in it. The instructions listed here,

http://www.nliteos.com/guide/

will show it a lot easier than I can explain it. You will come to a step where you can integrate drivers into the cd, this is where you need to know the location of that inf. You can also add and remove various Windows components while you're at it, but only one's you know you don't need/use (MSN Explorer is a big one for a lot of people to nuke out).

Once all of that is done you can either create an ISO of the new cd, or burn it directly to cd from within nlite. Then it is just a matter of booting from the cd (and ignoring the F6 to install drivers part) and installing Windows as usual.

#34 Catfish

Posted 03 June 2007 - 05:26 PM

Download and install nlite, and while you're at it download the latest drivers for your motherboard (ULI ® M1573Chipset, version 2.20),

http://www.nvidia.co...li_drivers.html

then extract the file using Winrar and locate the inf for the sata driver (going to need this for later. Next copy over your XP cd onto the hard drive, then run nlite and load the copied over cd in it. The instructions listed here,

http://www.nliteos.com/guide/

will show it a lot easier than I can explain it. You will come to a step where you can integrate drivers into the cd, this is where you need to know the location of that inf. You can also add and remove various Windows components while you're at it, but only one's you know you don't need/use (MSN Explorer is a big one for a lot of people to nuke out).

Once all of that is done you can either create an ISO of the new cd, or burn it directly to cd from within nlite. Then it is just a matter of booting from the cd (and ignoring the F6 to install drivers part) and installing Windows as usual.


Is there anything you can't do? :P

#35 DarkFall

Posted 03 June 2007 - 06:33 PM

Download and install nlite, and while you're at it download the latest drivers for your motherboard (ULI ® M1573Chipset, version 2.20),

http://www.nvidia.co...li_drivers.html

then extract the file using Winrar and locate the inf for the sata driver (going to need this for later. Next copy over your XP cd onto the hard drive, then run nlite and load the copied over cd in it. The instructions listed here,

http://www.nliteos.com/guide/

will show it a lot easier than I can explain it. You will come to a step where you can integrate drivers into the cd, this is where you need to know the location of that inf. You can also add and remove various Windows components while you're at it, but only one's you know you don't need/use (MSN Explorer is a big one for a lot of people to nuke out).

Once all of that is done you can either create an ISO of the new cd, or burn it directly to cd from within nlite. Then it is just a matter of booting from the cd (and ignoring the F6 to install drivers part) and installing Windows as usual.


Is there anything you can't do? :P


Be concise, maybe? :wasnt-me:

#36 Jac3624

Posted 03 June 2007 - 10:38 PM

Thanks Stormy, that's the 3rd time you've helped me out. :D

I'll try it out tomorrow, I just don't have the energy to do it now.


:edit: It worked. I got board so I decided to try it now. Now I have to install everything again.

:edit2: everything that I've done so far is either loading or installing much faster. I haven't even tried any games yet. I will soon and tell you guys how that goes. :D Thanks for the help!

#37 The_Curley

Posted 04 June 2007 - 09:19 PM

I just ordered this HDD: http://www.newegg.co...N82E16822136075



Keep your box and documentation. I wasn't kidding about Western Digital drives crapping out. You could have gotten a nice Seagate for a little more. VERY little, actually. HERE


i second that


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

Skin Designed By Evanescence at IBSkin.com